On May 12, 9:07*pm, "AWM" wrote:
"metronid" wrote in message

...
On May 12, 6:09 pm, "AWM" wrote:



"metronid" wrote in message

...
On May 11, 7:04 pm, "AWM" wrote:

Thanks for all the info Rich, the problem I actually have is a slight
distorted bubble appearance on the cd film that is preventing the
installation from installing completely. So I need to rebuild the cd, if
I
can figure out which files are not reading correctly off the cd...
mc"Rich/rerat" wrote in message

...

AWM,
If you are getting an error when trying to install with PB MRCD like:
"Installation has found that this in not a Packard Bell computer".
Or words to that effect, the following things could be happening.

1. You have upgraded the BIOS for the motherboard, that the MRCD does
not
recognize. I have a PB MM955 with a PB850 motherboard using Win98 FE..
When
PBell left the US in 2000, their support ended for this PC, and the
BIOS
upgrades ended at version 1.09. Even though there were additional BIOS
upgraded for that motherboard, but they were not designed for the
North
American machines. So the PB MRCD will not work those PC's, that have
the
newer versions of the BIOS. You will need to downgrade the BIOS.
2. If you added newer hardware such as video card, sound card, or
modem
card, or even a newer CD-ROM or DVD player, you may run into a
problem.
The
installation process looks for certain hardware, so it can install the
proper drivers for these devises. If they can not be found, because
you
upgraded, the process will also stop. Had this issue when I installed
a
video card to replace onboard video chip. The original solution, was
to
remove the video card, use the MRCD, then reinstall the video card.
Even
"disabling" the video on the board, using a jumper change did not
work.
So
you might need to remove some hardware upgrades you made. run the
MRCD,
then
reinstall upgrades and install appropriate drivers.

The following Work Around, is what I have used in the past, so I did
not
have to remove hardware when reinstalling from the MRCD.
1. Boot into DOS using the Win98 Boot diskette.
2. Using FDISK, set up the partitions.
3. Boot back into DOS. Place MRCD into CD-ROM.
4. Select either installation file from the MRCD in DOS to run
installation.
"X:\" being the CD-ROM designation in DOS. This will only install
Win98
on
your PC, you will need to install PBell hardware drivers and PBell
software
manually later:

X:\Win98\WINDOWS\OPTIONS\CABS\setup.exe
OR
X:\Win98\WINDOWS\WININIT.exe

5. Remove MRCD & Boot Diskette, from PC during the installation
process,
as
directed.
6. Once you get Win98 installed and you boot up it on the PC.
7. Place MRCD into the CD-ROM, when the installation window pops up,
close
it.
8. From the MRCD, Copy the following Folder directory:

CD-ROM:\Win98\WINDOWS\OPTIONS\

And Paste it into the following folder Directory:

C:\WINDOWS

9. From the C:\WINDOWS\OPTIONS\GTS folder, send a shortcut of the
STracker.exe file to the Desktop.
10. From the Desktop click on the STracker.exe shortcut, and you
should
be
able install the PBell bundled software that came with you PC now.

If your PBell is working right now, it might be useful if you locate
the
drivers for PBell hardware (modem, sound card, etc...) installed
through
the
Device Manager. And copy them into a separate folder, and back up this
folder. So it will be easier to reinstall the PBell hardware drivers,
after
you reinstall Win98. They are there in the MRCD, and CAB files in the
\OPTIONS\ directory, but it might be time consuming to locate & choose
the
right one.

--
Rich/rerat
(RRR News) message rule
Previous Text Snipped to Save Bandwidth When Appropriate

"AWM" wrote in message
news:HZBVj.16126$Au2.4049@trnddc07...
Does anyone know how I could scan my original PB Win 98FE cd and
locate
the
errors preventing the installation? I could use my stand alone win 98
FE
and
try to make a functioning cd....
mc- Hide quoted text -

- Show quoted text -

I am pretty sure you have a defective CD
What errors did you receive when using the CD.
The HD did have enough room ?
Was the HD empty?

I use Winimage to make a CDROM ISO IMAGE
If it fails you can check the size of each folder against the CDROM
and hope
that is the bad one

Also see by searching if you can find the cab files
You can install windows 98 right off of that

Depending on the encryption method the other PB files can be added
later.
Or not.

metronoid
The best I can remember(2 months ago) is that after it went thru a full
restore and rebooted I would get a can not write to disk error. I was
using
a 20 gig WD.
mc- Hide quoted text -

So windows did load from the CD.
It failed after reboot.
Did you format the HD first ?
Have you tried a boot floppy to see how much room is on the HD.
It may not *be the CD.

I did format the HD using the WD utility disk, and then I used a boot floppy
to start to load the cd. I do not remember
*if I checked to see how much room was on the HD.
mc- Hide quoted text -

- Show quoted text -

Sounds correct to me.
The PB CD usually tells if there is enough room.

I hope the utility did not partition the disk
Which I doubt


Get a win98 boot disk with fdisk on it
Look at the parttition info

I have a strange hunch
I could be wrong