View Single Post
  #9  
Old September 24th 03, 02:34 AM
Tim
external usenet poster
 
Posts: n/a
Default

Orhan,

Sorry for getting off on the wrong track.

You may be out of luck as the Gigabyte web site at:
http://www.giga-byte.com/Motherboard...r_GA-8KNXP.htm
lists the ICH5 RAID drivers as being for NT upwards only. No mention of
Win9x althought there is under the Intel Chipset drivers. Perhaps try the
list from this web page and *hope* that the correct driver combination is
installed under Win9x.

F6 bios does seem to have sorted a lot of issues. If you change the SATA
controller to RAID and then don't see it on the Boot Order list, then save
bios, shutdown, power off / wait / power on and go back in and check. This
bios (F5 and F6) has a horrid time with the the boot order menu.

For me to get this to work, I have the SATA RAID drivers installed under XP
& they are working even though the SATA disc is by itself and not RAID. The
Intel Raid manager app even works and tells me I have 'No RAID Volumes' but
with 1 "Non-RAID Disc". This is for Intel Application Accelerator RAID
edition v 3.0.0.2246 downloaded from Gigabyte page above.

If you can boot off the SATA drive in IDE config, then install the Intel
drivers then under Win98 - ensure you have the latest matching set of
drivers and F6 bios. Make sure you have the same driver versions also
installed in 2K before changing the SATA controller from IDE to RAID. It
does not matter if the drivers report or come up not working, the important
thing for W2K is that they are installed & ready to use if needed which they
will if you boot under RAID.

Then try configuring the SATA controller as RAID on Auto (IE not IDE), and
boot into Win2k / Win98.
For Multi boot to work, Win98 has to be installed first, then W2K. If not in
this order then you will need to 'patch it up' and that is an entirely
different issue.

Let us know how you get on. Does it boot when Raid under W2K? Do you get the
boot Menu?

- Tim




"Orhan" wrote in message
om...
Is there someone who has a single SATA HDD running as SATA UNDER 98SE,

please?

Orhan

"Tim" wrote in message

...
I went around this issue tons of times before I got it to work.
The *only* way it works on *this* mobo is with the Intel SATA as RAID -

even
though I am not using raid. This is completely contrary to what you are
saying, to what I was expecting, and how other SATA / PATA RAID

controllers
work. With the Intel SATA as IDE, the standard IDE1 and 2

disappear!!!!!!!!
This had me absolutely miffed for weeks 'cos it meant I had not choice

but
to use that horrid ITE device as an IDE device, which in turn elongated

my
boot times by 22 or so seconds.

I am more than happy to be proven wrong, but would suspect something

else
has been fixed first (EG m/b revision, bios).
I use F6 bios.

- Tim



"Taliska" wrote in message
...
IE when the intel SATA controller is configured as RAID you can boot

of
it,
if it is not, it has to be set to IDEx to boot and that removes the

real
IDEx from your machine.

Nope, nope....

Set the SATA to Manual and enable it - don't set it up as a RAID. You

can
then boot off it as a SATA drive and still have all your IDE's

available.
If
you can't set the boot order 'cos you can't see it, then enable all

RAID
controllers.

Taliska

"Tim" wrote in message

...
So, if SATA0_SB is Pri Master, you will no doubt not see IDE1.
If SATA0_SB is configured as SATA0, then your disc is not

recognised.

The onchip SATA controller works best if it is configured as RAID

even
if
you do not have a RAID config.
Unlike the ITE / Gigabyte controller which is absolutely stupid the

Intel
one is smart enought to see and run with ordinary non raid discs.

You
should
install the intel RAID drivers under XP in this config.

IE when the intel SATA controller is configured as RAID you can boot

of
it,
if it is not, it has to be set to IDEx to boot and that removes the

real
IDEx from your machine.

Clear?

BTW: when you look at the mobo in a tower case with the PCI's on the

left,
CPU towards the top, the SATA0_SB connector is the 'top right' one.

- Tim



"Orhan" wrote in message
om...
Hi,

I have a Maxtor 120GB SATA HDD and GA-8KNXP motherboard. I

configured
SATA Port0 as IDE Pri. Master in BIOS, because I couldn't install

XP
when remapped this to SATA0 (XP installer can't find my HDD).
How can I use my HDD as a SATA drive and not as PATA

(DMA100)-without
crashing my system- ? I run a dual boot system (98SE+XP) and it

works
fine except that SATA problem.
There is no SATA option available under Boot Order in BIOS (anyhow
disappeared!)
I am not sure,which connector did I connect my SATA drive to. But

I
think, to SATA0-SB. Is there any difference?
Gigabyte Technical Support says I should upgrade my F5 BIOS to F6.
Would that be a solution for me? In User's Manual of GA-8KNXP I

read
that this port must be remapped to SATA0 when running XP or later

OS
only. What if dual booting? And why didn't XP find my SATA HDD?
What is the right setting for BIOS?
I would be grateful for any helps.

Orhan