GA-8PENXP and Game Port header
The Pin outs for this game port header does not follow the same naming
convention as the standard. Can anyone out there tell me what these equate
to as compaired to the standard game ports? Below I have two columns, in
the first column is the Giga-byte pin out header for the game port as shown
in the manual. The nomenclatures for each pin is a little cryptic. I also
think that there was a mistype for pin 2, the book showed GRX1_R but I think
it should have been GPX1_R. Anyway, in the second column I have pasted
what I think these cryptic headers correlate to in the standard pin outs.
This is an index of what I think this cryptic shorthand stands for;
The VCC stands for +5V power.
GND = of course Ground
GPX1_R = Game Port X Axis 1st joystick (I don't know what the _R means in
these)
GPY1_R = Game Port Y Axis 1st Joystick
GPX2_R = Game Port X Axis 2nd Joystick
GPY2_R = Game Port Y Axis 2nd Joystick
GPSA1 = Game Port Switch, A Joystick Button 1
GPSA2 = Game Port Switch, A Joystick Button 2
GPSB1 = Game Port Switch, B Joystick Button 1
GPSB2 = Game Port Switch, B Joystick Button 2
MSI_R = Midi Switched Input
MSO_R = Midi Switched Output
Anyway, here is what i think the pin-outs should be, correct me if i am
wrong...
G-B Pin out for Game Port according to manual, with what I think the
matching standard pins should be.
1. VCC 1. +5V Power
2. GRX1_R 5. J1CX Joystick 1 Axis X
3. GND 7. GND Ground
4. GPSA2 13. J1B2 Joystick 1 Button 2
5. VCC 2. +5V Power
6. GPX2_R 6. J2CX Joystick 2 Axis X
7. GPY2_R 10. J2CY Joystick 2 Axis Y
8. MSI_R 14. Midi-In / Midi TxD
9. GPSA1 3. J1B1 Joystick 1 Button 1
10. GND 9. GND Ground
11. GPY1_R 11 J1CY Joystick 1 Axis Y
12. VCC 15. +5V Power
13. GPSB1 4. J2B1 Joystick 2 Button 1
14. MSO_R 8. Midi-Out / Midi RxD
15. GPSB2 12. J2B2 Joystick 2 Button 2
16. No Pin 16. No Pin
Standard Game Port Pin outs
1. 1. +5V Power
2. 2. +5V Power
3. 3. J1B1 Joystick 1 Button 1
4. 4. J2B1 Joystick 2 Button 1
5. 5. J1CX Joystick 1 Axis X
6. 6. J2CX Joystick 2 Axis X
7. 7. GND Ground
8. 8. Midi-Out / Midi RxD
9. 9. GND Ground
10. 10. J2CY Joystick 2 Axis Y
11. 11. J2CY Joystick 1 Axis Y
12. 12. J2B2 Joystick 2 Button 2
13. 13. J1B2 Joystick 1 Button 2
14. 14. Midi-In / Midi TxD
15. 15. +5V Power
16. 16. No Pin
I currently have a FrontX front panel and internal game port setup
(
www.frontx.com) and must move the pins to match my MO-BO. I wanted to make
sure of the pin-out conversion before I started. Any light on this subject
would be a great help...
Thanks..