quick mobo mounting question
Hi,
My case (Nexus Breeze) has been supplied with small metal clips and screws with fibre washers to mount the mobo. I'm installing an MSI board and I wonder if I should use thease washers as they will insulate the top of the board from the chassis. So, insulating washers or not?? Mike |
On Fri, 27 Aug 2004 11:56:45 +0000, Spock wrote:
Hi, My case (Nexus Breeze) has been supplied with small metal clips and screws with fibre washers to mount the mobo. I'm installing an MSI board and I wonder if I should use thease washers as they will insulate the top of the board from the chassis. So, insulating washers or not?? Shouldn't matter. I've never used them on hundreds of builds. Well, maybe I have just to get it out of my sight. But metal clips? I'd be careful with these and I don't know what they are unless you're talking about brass standoffs which are common. -- Abit KT7-Raid (KT133) Tbred B core CPU @2400MHz (24x100FSB) http://mysite.verizon.net/res0exft/cpu.htm |
"Wes Newell" wrote in message news:pan.2004.08.27.17.27.43.25726@TAKEOUTverizon. net... | On Fri, 27 Aug 2004 11:56:45 +0000, Spock wrote: | | Hi, | | | My case (Nexus Breeze) has been supplied with small metal clips and screws | with fibre washers to mount the mobo. I'm installing an MSI board and I | wonder if I should use thease washers as they will insulate the top of the | board from the chassis. | | So, insulating washers or not?? | | Shouldn't matter. I've never used them on hundreds of builds. Well, maybe | I have just to get it out of my sight. But metal clips? I'd be careful | with these and I don't know what they are unless you're talking about | brass standoffs which are common. | Just speculation, but many lower cost cases come with "square" standoffs that clip onto the case as opposed to being screwed in. I believe this is what he is referring to. Depending on the size of the top of the clip (where the threads are .... the part that will sit against the motherboard) you may want to go ahead and use the insulators on them. The only ones I have ever seen were still small enough to not cause a problem, but just check to make sure you wont be shorting any traces on the PCB with the clip type standoffs. |
:: Just speculation, but many lower cost cases come with "square" :: standoffs that clip onto the case as opposed to being screwed in. I :: believe this is what he is referring to. Depending on the size of :: the top of the clip (where the threads are .... the part that will :: sit against the motherboard) you may want to go ahead and use the :: insulators on them. The only ones I have ever seen were still small :: enough to not cause a problem, but just check to make sure you wont :: be shorting any traces on the PCB with the clip type standoffs. Thanks for the replys. Yes, they are the square metal standoffs that just clip into the case, the tops are small enough not to cause any shorts. I don't see how it is possible to put the insulation washers UNDER the board, without resorting to glue or something to hold them in place, it seems it's not important anyway. Thanks again. Mike |
On Fri, 27 Aug 2004 17:27:41 GMT, Wes Newell
wrote: On Fri, 27 Aug 2004 11:56:45 +0000, Spock wrote: Hi, My case (Nexus Breeze) has been supplied with small metal clips and screws with fibre washers to mount the mobo. I'm installing an MSI board and I wonder if I should use these washers as they will insulate the top of the board from the chassis. So, insulating washers or not?? Yes they're ok !. Common fare since the K6-2 Shouldn't matter. I've never used them on hundreds of builds. Well, maybe I have just to get it out of my sight. But metal clips? I'd be careful with these and I don't know what they are unless you're talking about brass standoffs which are common. Like you Wes, I use the brass turrets, but providing the fibre is twixt the screw and the MOBO top they seem ok. They are however an ' iffy ' item, cheap-as-chips proper brass turrets can be had from any OEM supplier BoroLad |
On Fri, 27 Aug 2004 19:32:16 GMT, "Spock"
wrote: :: Just speculation, but many lower cost cases come with "square" :: standoffs that clip onto the case as opposed to being screwed in. I :: believe this is what he is referring to. Depending on the size of :: the top of the clip (where the threads are .... the part that will :: sit against the motherboard) you may want to go ahead and use the :: insulators on them. The only ones I have ever seen were still small :: enough to not cause a problem, but just check to make sure you wont :: be shorting any traces on the PCB with the clip type standoffs. Thanks for the reply's. Yes, they are the square metal standoffs that just clip into the case, the tops are small enough not to cause any shorts. I don't see how it is possible to put the insulation washers UNDER the board, without resorting to glue or something to hold them in place, it seems it's not important anyway. Thanks again. Mike Used to also think . . ' solder bath ', but no, they go ' topside '. BoroLad |
All times are GMT +1. The time now is 07:51 PM. |
Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
HardwareBanter.com