HardwareBanter

HardwareBanter (http://www.hardwarebanter.com/index.php)
-   Overclocking AMD Processors (http://www.hardwarebanter.com/forumdisplay.php?f=12)
-   -   Athlon XP 2200+@2700+ (2166 Mhz) on A7N8x-x: BIOS's revenge (http://www.hardwarebanter.com/showthread.php?t=12443)

M Arino October 10th 03 09:46 PM

Athlon XP 2200+@2700+ (2166 Mhz) on A7N8x-x: BIOS's revenge
 
Hi there,

I am new to this NG, I want to comment on my first OC experience.
I had bought the parts for my new system in the course of a few weeks,
and finally had time yesterday for the assembly. All was fine, even
the OCing at the final speed (with stock Vcore), but as I saw pretty
low temperature in idle mode, I decided to OC the FSB a bit more.
Then I got corrupted BIOS screens. The BIOS flash program wouldn't
work, but at some point the system went, after two hours of booting
and showing corrupted BIOS screens, into default settings (sort of).
Then, the BIOS stopped showing corrupt screens, I restored the 13*166
and all was good (17% Mhzs increase at first try was not too bad for
me)
BTW, my memory is TwinMOS PC3200, the lowest number of the latencies
was 2.5 and the highest 7. Do you think I can run this memory with
more agressive timings?
I read in the NG about getting a spare BIOS chip and doing some hot
flashing when I get corrupted BIOS problems, where do I get such a
BIOS chip? I don't want to venture into hardcore OC if I have to
worry about corrupt BIOS.

Thanx for the help,


Miguel

BooTwo October 11th 03 05:40 AM

All I can say is welcome to nforce 2 overclocking; I just went through this
with my first nforce 2 board.

You tried resetting the cmos, right? Also different people sell reflashed
bios chips or reflash yours (I think badflash.com is one, no plug, I never
used them but did research this). I reset my cmos, tried reflashing several
times, finally it took.

I have to say you shouldn't flash from the windows flash program at this
point but that's my opinion.

I have buffalo memory with twinmoss chips; I run 2.5 3 3 7 or 2.5 3 3 11
since I'm finding my overclocking limits ike you are.

I wouldn't change the memory timings while trying to overclock and make sure
the last "3" is there.

Good luck, smarter people will soon reply
"M Arino" wrote in message
om...
Hi there,

I am new to this NG, I want to comment on my first OC experience.
I had bought the parts for my new system in the course of a few weeks,
and finally had time yesterday for the assembly. All was fine, even
the OCing at the final speed (with stock Vcore), but as I saw pretty
low temperature in idle mode, I decided to OC the FSB a bit more.
Then I got corrupted BIOS screens. The BIOS flash program wouldn't
work, but at some point the system went, after two hours of booting
and showing corrupted BIOS screens, into default settings (sort of).
Then, the BIOS stopped showing corrupt screens, I restored the 13*166
and all was good (17% Mhzs increase at first try was not too bad for
me)
BTW, my memory is TwinMOS PC3200, the lowest number of the latencies
was 2.5 and the highest 7. Do you think I can run this memory with
more agressive timings?
I read in the NG about getting a spare BIOS chip and doing some hot
flashing when I get corrupted BIOS problems, where do I get such a
BIOS chip? I don't want to venture into hardcore OC if I have to
worry about corrupt BIOS.

Thanx for the help,


Miguel




Lurch October 11th 03 06:14 PM

"M Arino" wrote in message
om...
Hi there,

BTW, my memory is TwinMOS PC3200,
the lowest number of the latencies was 2.5
and the highest 7. Do you think I can run this
memory with more agressive timings?


My 512Mb TwinMos PC2700 (333 MHz 2,5-3-8-3)
is running @ 384 MHz (2-2-5-2) with a little voltage increase (2,8 v)

and I've added a Vantec copper heatspreader, just to be safe ;-)

You can expect 420-440 MHz from your PC3200, I guess

Lurch




All times are GMT +1. The time now is 03:30 AM.

Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
HardwareBanter.com