Can someone explain this to me? I have an Intel core-2 duo system and I just installed 2GBs of PC4200, 533Mhz memory which (supposedly) has the following timings: 3-3-3-8. When I checked cpu-z, it shows me three columns as follows: Freq: Timings 1. 200Mhz: 3-3-3-8

Hi, I read lately an article in a local newspaper, that stated that if I have a motherboard that is build to use PC3200, I could also use PC4000 and even DDR2 memory modules What I would like to know is , IS this true, I know that I would not get the whole performance gain from those memory...

I just bought some new ram to upgrade my system,the problem is,it wont work on my p.c. I have an M.S.I. 875p neo m/b,intel p4 2.6 cpu,512mb ddr pc3200 400mhz ram & windows xp. The new ram is, 1gb ddr pc2700 333mhz. When i fit the new ram either on its own or with the original ram, the system...

I want to add 1 Gb memory to my existing 512Mb I have a Giga-Byte GA-7VTXE motherboard which supports DDR SDRam The existing memory type DDR PC2100 is in the first slot of 3 I will get 1 Gb DDR PC3200 to add My question is: will it make any difference in which slot I put the new memory? i.e. is it...

Andy/Bandi wrote: To All Cognoscenti, Greetings! My Foxconn Winfast K7S741MG/K7S741GXMG motherboard has 512 MB of memory installed. I'd like to increase it to 1 GIG. What kind of memory should I purchase? Thanks in advance, Andy

I currently have 64MB SDRAM 100MHz Memory on my PC, I want to upgrade it, if I bought for example: 512Mb PC3200 184pin DDR 400 DIMM Memory which I found at http://www.savastore.com Would I able to add it to my current RAM or is it best to take out the 64MB SDRAM and replace it with the new one...

After installing the new module the PC won't boot. No initial video screen, no CMOS setup, no error beeps, nothing! I removed both modules and installed only the new one. Same thing. Remove the new module and installed the old module and the system runs fine. Mainboard: FIC AU-13 CPU: AMD...

Intel's support is a series of unanswerable emails, so here goes. I have an Intel MOBO D865PERL looking to upgrade my memory. I currently have two sticks of 256 MB PC2100 and thinking about upgrading to this memory: Speed: DDR333(PC2700) Type: 184 Pin DDR SDRAM Error Checking:...

i have a Gigabyte 7ZX motherboad with 256mb ram, i am tring to add an extra 512mb, but it wont read more then ~300mb and then wont even boot into windows, any ideas?

I'm trying to work out what parts of my Windows PC's memory are free. You know when you do computer_management-disk_defragmenter-analyze, you get a graphical representation of where your files are on your HD. Is there anything similar for the memory? So I can see what's put where.

Hello I've been using 2 gigabytes of OCZ Platinum 6400 for a few months now with no problems. Recently I was experiencing problems when loading games so I ran memtest which discovered errors when reading and writing from the RAM. The RAM is running at its rated timings of 4 4 4 15 1T at 2.1V. I...

Sandra 2007 gives me this warning: Warning W2523 - The memory bus speed exceeds the module speed rating. While most memory will operate at slightly higher speeds, this is not recommended. Consider buying higher rated memory. Fix: If the memory bus speed always equals FSB for your system,...

I'm running a Dell Dimension 4500S with PC2100 256mb SDRAM 266Mhz, non-registered, non-ECC memory and I'd like to increase performance with a 1gig stick or 512k minimum. I went to Circuit City and all they have is PC2700 sticks. The salesman said PC2700 is backward compatible with pc2100 and I've...

Is there a way to find out if ram memory was previously overclocked ? I have some utility tests as memotest and other but how to see if memory was overclocked before my usage ? Moreover, what kind of effects could that do to using that memory again at normal timings and frequency? Thanks

I have been having computer trouble (see below) and the first thing I found during my tests was that memtest86 reports me as having only 1023 megs of ram. I have always noticed that during boot-up the memory test sort of goes normal speed to 1023 then sort of rolls as an afterthought to 1024, but...

Memory: Stick fully inserted even though no click? One slot affects another? I finally have this fixed, subject to my quesiton in my previous thread, but at least 6 times I had installed RAM in the slots and it didnt' regeister correctly. Alone, each pair of sticks seem fine. When...

Memory: Does it matter if big DDRs are firsr or second? Posted to alt.comp.hardware and alt.sys.pc-clone.dell, since the computer is a Dell and I started the topic in that group, but have broader questions now. I have two 512M and two 1G DDRs and they are the same speed PC2700, the same 333,...

I'm trying to run a Memtest on my computer. It tells me I should run 2 programs simultaneously for best results. How can I get it to run 2 separate programs at the same time? It won't let me get past the advisory msg. Thanks.

I recently used memtest86 after experiencing many serious system instabilities (random file corruption, system crashes). Basically memtest would report thousand of errors in a matter of minutes.Turned out the the problem was caused by a faulty Bios setting (memory was set to 'performance mode'....

I have a Biostar M7NCD Pro (nforce2) motherboard as the basis of my homebuilt. It has been running without a hardware problem for about 11 months. I've used five different PC2100 sticks of various sizes and manufacturers in many combinations, in the Biostar and in a Dell 4500 (P4, Intel 845...