"CSX" wrote in message ... Hi Setting up a new PC using the K8N Ultra SLI Got a single Hitachi SATA2 drive. trying to load XP. BIOS doesnt seem to recognise it. Nor does windows. Done the F6 load drivers and tried...

Wondering if anyone can help. Am I able to run 2 SATA drives off the Intel ICH5r whilst having IDE 1 and 2 occupied by a DVD writer, CD writer and DVD ROM? I am finding that I can have drives connected to either Intel SATA ports or the IDE ports 1 and 2 but not both at the same time? At the...

http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&category=40158&item=5231589018

I have a Giagabyte GA-81PE1000-G (Rev. 3)Titan motherboard 2004 GT edition, running a Pentium4 Prescott 2.8GHz CPU (FSB 533MHz), with 512MB of DDR RAM (2 sticks of 256MB each). My OS is Windows XP Pro. When using any IDE HDD - Maxtor 80GB, WD 80GB or Maxtor 40GB, amongst others - the computer...

I've got Gigabyte GA-81915G PRO motherboard and on-board sound C-Media 9880. Recently I installed TV Tuner AverMedia 303/403. Unfortunately I can't hear any sound from my speakers. I checked TV Tuner's audio-out and it's working properly. When I connect Tv Tuner's audio-out by cable to Line-in...

BAD BIOS CHIP FLASH? VISIT: http://BadBiosFlash.com For Replacement chips $16 re-flash of existing chip $8

I have a Gigabyte GA-7vax. It doesn’t want to want to post or turn the computer on. As I press the power button. I notice the fans begin to move, then stop. The RAM LED light then comes on. Nothing else comes on. Any ideas? My system consists of: Antec 350w Maxtor 60gig Radion 9000 128mb

Hi, Does anyone know if it is possible to use (PC800) 2 x 1GB Modules in the GA-8IHXP? Is there a list available of RDRAM Modules which have been tested with this board? Thanks

Can someone advise on the best way to overclock a A64 3000 venice on this board. A web page would help! Thanks Wad

I can't get either of my 56k PCI modems to fully connect to my ISP on the 81955x Pro m/board. They're fine elsewhere. When I dial it's ok, then it takes forever to handshake and emits a sqeal for about 30 seconds, then after it's verified username and password (which also takes far longer than...

Hi, I solved my problem... The C-Media codec chip cannot drive headphones correctly. I connected the output to my amp and speakers and it sounded much better. When driving headphones (I tried two sets, AOpen and Sony) the bass is missing and the trebble is boosted. I checked the data sheet of the...

Hi folks, My PC has a 7VAXP with SPDIF output, but I cannot seem to get something on SPDIF coax output under W2000 + media player. My digital preamp (NAD 118) seems to have problems synchronising with PC data stream. - In the sound control panel, I selected SPDIF output and made sure "mute" was...

Hi, I've had one of these in a PC for a couple of years and now want to use the RAID feature, but when I go into the BIOS the serial ATA Mode item is missing. In all the manual versions that I've downloaded the BIOS date shows 1984-2004, but mine shows 2003, and at boot shows -L F2. Will a BIOS...

I got a GA-7NNXP motherboard. When I boot Windows XP from a drive connected to the Gigaraid controller, I see my SATA drives in the Windows XP explorer. When I boot Windows XP from a drive connected to the SATA controller, no drives of to the Gigaraid controller are shown. The Gigaraid controller...

Hi. I have the 8INXP board. (It has 2 IDE ports in the chipset, 2 IDE ports using the Promise controller, and 2 SATA ports using the Silicon Image 3112 controller.) I have WinXP running from a 60GB drive (7200 rpm, 2MB cache) connected to one of the chipset IDE ports. I just bought a 300GB drive...

"Burnhard" wrote in message My PC won't boot up. I'm getting a PC speaker sound when I start it and then it shuts down (doesn't get as far as initialising the gfx or anything). Can't find...

On Sat, 30 Jul 2005 22:15:18 +0100, Pun Krocker wrote: Hi, Decided upgrade the system to AMD 64. Can someone tell me what is the difference between using s754 and s939 mobo's please?

I've had my XP 1500+ (Palomino core) in a shuttle AK31 for the past 4 years, but the board recently died. I replaced the shuttle with the 7VT600P-RZ, so that I can continue using my existing cpu (266 FSB) and RAM (PC2100). My cooler is the same as it has been the last 4 years- a thermalright SK-6...

When I got this mobo it originally came with BIOS F6 and everything seemed to work fine but when I upgraded to either F8 or F9b I ran into numerous problems. #1 the CMOs setting keeps resetting. If my CPU was overclocked, sometimes it'd revert to default speed and once it claimed I had 2.0GHz P4...

I have updated this section to prevent any further confusion: " Data bits: a,a,a,a,a,a,b,b,b,b,b,c,c,c,c (these bits can have value 0 or 1) " (Since some people though these aaaa, bbb, ccc bits behaved like unary encoding (all ones or all zeros) This is not the case.