Is it normal for the motherboard to read higher than the cpu. At the moment the motherboard reads 32C and the Cpu 26C This does not seem right to me. This is in Everest info but it is the same in Bios when read there, motherboard temp higher than CPU. The other thing has anyone managed to run a...

"Burnhard" wrote in message My PC won't boot up. I'm getting a PC speaker sound when I start it and then it shuts down (doesn't get as far as initialising the gfx or anything). Can't find...

Hi, I have an issue with this board running stable at stock settings. I just got it up and running but it is unstable with RAM at 400MHz. I am using BIOS F8b, a 2.6C P4, Kingston HyperX 3500 512 stick, WD 120GB SATA drive, ATI AIW 7500 video, and Antec 380W True power in a Sonata case. I have no...

Hi, I have a very strange problem. My setup is an E4300, GA-965P-DQ6, Leadtek PX7950GT 512, 2Gb of Corsair XMS2 ram (800/6400 and 5-5-5-12 timings) with a 500W PSU. If I alter the FSB or PCI-E speed at all, even if I do not change it from default (200 and 100 respectively), when I save the changes...

Can someone advise on the best way to overclock a A64 3000 venice on this board. A web page would help! Thanks Wad

Help? My problem: My LAN connection keeps dropping. Will run for a while but then the connection just kicks out. Sometimes it will reset by itself, other times I must reset the modem. Left idle no disconnection until I start to download data. My setup:

I have just recently upgraded to the GA-8KNS Ultra 939. At present I havea Maxtor 80 GB HDD ATA 133. I work wit a lot of large files so my HDD takes a lot of thrashing. I dont really want to spend a lot of money so I thought I would add an additional 80 GB HDD and set it up as RAID 0. After...

Hi, K8NS Ultra-939 - Why no +5v readout? The BIOS only shows 3.3. and 12v and combined. My 5v rail is also all over the place (e.g. 2.17 up to 5.4) using mbm5 and Speedfan, yet the computer is stable and my 5v rail is good using a multimeter. I thought it was a bad board so I RMA it and its the...

Hello, I went into the bios, i put the ram (333) up to (356) worked fine, do i need to also give it more frecency? I put the ram up to 402 and it wouldnt work. CPU is set to 1xx? with the option to go up to 5xx? so i did and it didnt work. How high can the CPU go, and do i need to give it more...

Just put a Sata drive in (VAXP-A Ultra), ME installed but XP doesn't find drive as an install option and no option in bios to set Sata drive as boot option Any ideas Grahame

G'day all, I'm planning on getting a new computer soon, and will move a few components over to the new system. Among them is a Sound Blaster Live. How does the SB Live compare with the on-board audio in new motherboards? For example the Gigabyte 8IPE1000 Pro2, or the newer socket 939...

Hello All, I've got a GA-6BXC (an old BX based MB), and it supports 100MHZ and 66MHz FSB properly. It also supports 133MHz FSB, but the AGP runs at about 89MHz instead of 66. Is that a bad thing? My situation is this: This is one of the few boards I have found that has 3 ISA slots, and can use a...

I have no idea about the commands or anything, but if you're wondering if you can use the 2600+ on your 7DXR, then the answer is maybe. You need: 1 - a 2600+ processor with a 266MHz front side bus (not 333MHz) 2 - the latest bios which I think you have (F10?) You should have a look at the gigabyte...

I have a 7DXR+ and I've connected a 200GB Seagate drive onto the normal IDE channel (not RAID). I'm using F9, with Windows XP sp1, and all is well. I haven't tried it on the RAID channels, maybe try it on the normal channels, and see if it works. -- Vu.

Hi all, I recently got a Leadtek 6800GT, but my system fails the POST when I put the card in. My motherboard doesn't seem to support it. My system is: CPU - AMD AthlonXP 1800+ Motherboard - Gigabyte GA-7DXR+ RAM - 1GB, mixed brands PSU - 400w (dunno the brand) Graphics -...

Hi all, Does anybody know if there's a maximum hard disk size that this board can recognise? I'm using the latest BIOS, F9. I'd like to get a hdd at around the 200GB mark, but there's no info on the gigabyte web site that will tell me if this is acceptable. Thanks. --

I have one of these boards and I want to clear the supervisor password from the system, but it is resisting all attempts to do so. Is there some way it can be cleared?

Allow me to start by stating that I've not only searched everywhere in other forums, but I've also read the following post below several times to try everything available: http://www.hwkb.com/Uwe/Forum.aspx/mainboard-gigabyte/3587/Gigabyte-965P-S3-problems-with-SATA-Hard-Drive-help I have a...

Hello all, I have tried installing more than 512 megs of ram on my motherboard and gotten errors. Anyone else have these problems or a possible solution? Thanks, Vic Geil, pc400 ddr 512megs, two sticks K8NNXP with an AMD 3400+ processor

Hi all, just one simple question: where can i find a detailed changelog for the bios versions of gigabyte motherboards? Or, in particular, for my mb: 7N400 Pro2 rev2. Thanks in advance, regards! V