Aussie, on your reply to a recent post by Rob about the 7VAX you mentioned you had your Barton 2500 running at 2200on a 7VA, is it the early rev board with the 3 position clock selector or did you unlock the cpu with the wire trick on the board in the socket or under the cpu between the pins? I...

I have been having a problem when trying to read/write from DVD writers. Basically, reading/writing causes the HDD LED to light up pretty much continuously, causing the PC to become somewhat less responsive. It does write discs successfully, but you can see the cache empty many times during a...

tyvm

tietac lost his hosting and uploading only newer ones if you have the bios(bioses) please U/L them or supply a link for some one who actually likes thier gigabyte but wants a bit more also any1 heard of a modd bios for their socket A (-p) dualie TIA

re ga7n400 pro 2 rev1 has a fan on the northbridge wrote in : Hello, I'm looking to get a used motherboard. Can anyone tell me what is the difference between v1 and v2 of this board? Is it always best to get the latest...

I wonder if someone can give my friend any advice. He has a Gigabyte 7NF RZ with a Sempron 2200 (I think it is that) CPU and because his readings showed it only had a 994 mhz speed he tried to alter the settings (not flash it) in the BIOS. He said he changed some settings but he can't remember...

Is it possible that the wrong jumper settings of a Slave Hard drive could destroy a Motherboard (GA-7n400 pro2) I won't bore you will all the details but someone I know had a Gigabyte 7NF RZ but after he went into the BIOS the motherboard suddenly packed in..............would not boot up. I...

I have a SATA HD pre-corruption problem with Silicon Image 3512 and WD Raptor 360GD on GA-7N400 pro2 rev2.0. My problem is the EventID 51 "...error in device\harddisk2\D during the paging operation." I tried both BIOS 4.3.33 and 4.3.47 for raid controller but the error persists. I tried RAID...

I bought a Maxtor ATA 133 80GB hard disc to put in my GA-6VXDC7 run PC (with two PIII 733 CPUs). When I run the bios to auto recognise / install the hard disc the PC locks up and a reboot is the only way out. Using it as a slave to my IBM 10.5GB hdd it shows as an identical size drive to the...

Just as a matter of interest what is the fastest Duron that will work on this m/board??

Purchase the above board in late may, and I just notice that the memory bank #2 is not recognizing the memory, change bios, change memory, installed different configurations on different memory banks, and got the same result. Any help will be appreciated, GA was not of good help, they toll me to...

Installed new Antec power supply to this board. Boots etc BUT sounds an alarm the whole time it's on. Antec manual says mobo "may not detect fans running less than 950 rpm and will sound alarm." How do I turn off alarm? Bios chip set features show "Fan Fail Alarm" have it set to "NO" but alarm...

Hi I have just bought a new case and i am having trouble hooking up the front audio ad the pins provided with the case don't match the names in the motherboard manual here is the motherboard pin settings 1.MIC 2.GND 3.MIC_BIAS 4.POWER

this is the new error ive been getting when trying to install xp pro onto my GA-8I915P-Duo A......" The procedure entry point GetProfileStringA could not be located in the dynamic link library KERNEL32.DLL" i get that error twice while trying to install windows but installation keeps going after i...

i am having serious errors installing windows xp pro on my 36 gig raptor....im not sure if its a mobo problem or somthing else but during installation i continually get the blue screen of death and the "page fault in nonpaged area" error message. a couple of times i actually got through...

Restored from backup after some major battles with my board drivers etc. All back to OK status but the GigaRaid Manager won't run in XP, I checked and the correct version of drivers are installed ITE IT8212 v1.6.1.8. If anyone has stumpled on a solution for this then please let me know, any help...

Greetings all, I just installed my son's Christmas motherboard/chip. (Amd 64, GA-K8U-939, 512k ddr, ATI Radion X700, 2 HDD, 2 CD rom.) When I put the mobo and new chip in, I fdisk, repartioned and formatted C. Broke C into two new partionions, C: 20G and D: 20G, then intalled WinXp onto C. After...

I have 6 Maxtor DiamondMax8 40G drives, all have identical labels but only four setup correctly with a Mirror. The exact difference is 2x39204 MB vs. 4x39205 MB on these disks. Any idea now to fix this?

It's time to move into the 21st century and rebuild the PC's. I am currently running a couple of Asus A7V133's with Amd XP2100+ CPUs. I am looking into a switchover to the GA-7NNXP mother board w/AMD XP3200+ CPUs. One of the reasons for using this board is onboard audio and the fact that it has...

I have an Gigabyte ep35c-ds3r motherboard running both Windows XP and Windows 7. I'm about to buy a 3TB hard drive. Would this motherboard support it? If not, is there a new driver update to make this possible?