Has the GA-7VT600-L got any multiplier adjustment??????? TIA

If I disable the onboard LAN in the BIOS it also disables the Gigaraid controller although the Gigaraid controller indicates enabled . Any idea why?

Got a Ga-7DXR+ M/Board = Can i use a 8x graphics card on this 4x motherbaord? The AGP card will be a geForce 6200 256mb 8x. THANKS GaZ

My problum is that i can not even find this board listed on there web site the closestes one i could find is http://us.giga-byte.com/Server/Products/Products_ServerBoard_GA-6VTXDR-C.htm But its drivers are no good for the raid. I bought this MB used and asside for the driver issue i have no...

Well after three weeks of trying everything (suggested by posters here) from using default IDE drivers, to disabling USB, taking out the sound card, replacing ram, etc etc, I've sent back my SATA II drive for a repair/replacement. Regardless of what I'd do, when the SATA controller was enabled on...

Bios Version : F7 OS : Windows XP Pro SP2 Controller : NForce4 Ultra (Not Sil) I seem to be having an issue whereby the K8NXP-9 seems to hate SATA-II drives, to the point where my Hitachi Deskstar 7K250 just locks up the whole system after sustained read or write operations in Windows. Tested...

Does anyone know if this board supports 300+ gb hard disks? Specifically i wanted to buy this HD: HDD EIDE MAXTOR 300 GB 7200 RPM ATA/133 BUFFER: 16MB SEEK TIME: 9.0 MS Thx in advance.

My second mobo GA-8KNXP Ultra rev 2.0 died I have to agree that it is probably underpowered, especially when we don't know what video card you are using. It's too bad that guys like Greg Vederman of PC Gamer magazine are still recommending 300W power supplies in both low-end and mid-range...

Thanks Kris, Never thought about being under powered . This could indeed be the cause for the problems. Will go out and buy something similar you suggested and hope that giga will repair this mobo also Dont think they will be happy with me :( at least they give good service Gtz, Herman

My second mobo GA-8KNXP Ultra rev 2.0 died :( within a week error continuous short beeps could it be a lack of juice? -- anyone have an idea about this ?? i'm using zalman powerunit 300 W (see below my system) My 1st mobo:cpu fan power failure and later cmos error. it was replaced by...

Dead GA-8KNXP Ultra rev 2.0 Got a new mobo from Gigabyte -NL last week :) After 4 months no power on the processor fan, repaired, got it back in week later Now after 9 month CMOS error ' after a week I got a new mobo :)

I bought a 1U server made by Colomachine (Model CM52 ) from eBay. I am trying to upgrade the on-board P4 2.4GHz processor to a P4 3.06GHz processor with hyper-threading. The motherboard used in the 1U server is made by Gigabyte GA-8LD533(-P). I can't seem to find any information...

http://www.chaintech.de/PRODUCTI/mainboar/socket7/5SSV.htm

Hello, This may be useful or informative to those of you who install Heat Sinks and Fans on your processor on the motherboard. I am building a new AMD-based computer... XP2600+ 333 on a GA7N400 Pro2 MB. When putting on the new heatsink, I decided to take a few hours trying different heat sinks &...

I can get Windows 2000 Advanced Server and Windows XP to install just fine. Windows 2003 (different versions, different media, etc) always hangs during the device installation phase. My set up is: 2xPIII 800 1024 MB RAM (Kingston 256MBx4/PC133) ATI Radeon 7500 Promise SX4000 RAID Card (RAID1 for...

My card has the latest BIOS I've tried the current drivers, the "beta" drivers (which are older) and the version before that. My next step is to remove the Promise card and see if it'll take directly to IDE0... "Tim" wrote in message ...

Technically I'm no candidate for Raid0: not much Photoshopping, no video editing.... But I'm a closet type A and the faster my applications (like MS Word....) start up, the less stressed-out I am. If I go to Raid0, will I notice the diff for that kind of use? If so, are 4 drives twice as fast as...

Last nite my EP45-DS3L suddenly would not boot - no power light, no mobo led, nothing. This followed a few losses of power due to a flaky surge protector under the desk. First thing that occurred to me was that the power supply had bitten the big one. But I swapped it out for a known good power...

EP45-UD3L. When I run the video transcoding app "HandBrake" with "Normal" CPU priority, I get intermittent beeps from the mobo. Setting it down to "Below Normal" (in Process Lasso's scheme of things...) the beeps go away almost completely. Kicking it up to "High", makes Windows XP appear to...

Family member has an HP 8200 https://www.amazon.com/gp/product/B017S118BI/ref=oh_aui_search_detailpage?ie=UTF8&psc=1 which, as far as I can figure, has an Intel Core i5-2400 socket LGA-1155 CPU in it. Both mobo and power supply appear to have bitten the big one. Tried a replacement power supply...