A computer components & hardware forum. HardwareBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » HardwareBanter forum » Motherboards
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Post New Thread
Threads in Forum : Gigabyte Motherboards Forum Tools Search this Forum Feed Icon
  Thread / Thread Starter Last Post Reverse Sort Order Replies Views
GA-7VA Reseting by Alan
I've tried searching the group for an answer to this, but with no luck. Can 400MHz DDRs be used with the GA-7VA board or not? I've just built two identical systems with the above board, 512Mb 400MHz DDR, AMD Athlon XP2600+ and Asus 64Mb Geforce 4 MX440 card. Both machines insist on rebooting at...
July 27th 03 10:10 PM
by Stan Mould Go to last post
9 645
Gigabyte GA-7N400 Pro by Richard
Hello I have just upgraded my PC and am having a few problems. Any help or comments would be appreciated. Original system was based on an AMD Athlon 500 mHz, 1287MB RAM, 10GB HDD, CD, DVD, CDRW with PCI modem, sound, TV and network card, 1x AGP ATI RAGE 128 graphics card running off a 250W PSU....
July 27th 03 09:36 PM
by boh Go to last post
1 373
8KNXP ITE suffers BAD performance... by modem
Earlier today I decided to do a comparison of the ITE Gigaraid IDE chipset vs a standard Promise UltraTX2 IDE PCI adapter. I did this after I read a few comments over the past few months that suggest the ITE Gigaraid chipset is very subpar. All of my tests were ran on a clean fresh Windows 2000...
July 27th 03 09:34 PM
by Bob Davis Go to last post
7 621
Slow HDD performance by Fred Klingenmeier
You need to update your raid drivers, not nVidia drivers. After raid was set up Windows XP did so automatically in the Windows update drivers section. "sid" wrote in message ... Gigabyte GA-7N400Pro (nForce 2) matched with ...
July 27th 03 08:53 PM
by Fred Klingenmeier Go to last post
0 611
GA-VA m/b by Lola Mackey
hi all, does GA-VA m/b has LAN incorporated? (some adv's say Yes, some NO? btw, is it a good m/b? rgds fr --
July 27th 03 07:55 PM
by Lola Mackey Go to last post
4 401
8INXP - DPS power failure by Richard Dower
OK...so it seems i have now encountered this strange error message. I had a 56K modem installed on the last PCI slot, PCI 5...i took it out because i got DSL. Then when i booted up i got the power failure warning. I am not sure if in fact it had anything to do with removing the 56K modem, or if it...
July 27th 03 06:14 PM
by Richard Dower Go to last post
2 540
GA-7NNXP or 7N400 ... dual channel mem with four dimms by Harry Muscle
Reading over reviews, I've noticed that the Gigabyte GA-7NNXP and GA-7N400 have four dimm slots. Does anyone know if dual channel operation is possible with all four slots filled? From what I recall, the NForce chipset only support 3 dimm slots, which means that the only way to have dual channel...
July 27th 03 02:55 PM
by Mr SUHA SIRMAKES Go to last post
4 716
81NXP for sale (toronto) by La Pedrera
I am selling this board. I've upgraded to something supporting the 800 bus. Board is approximately 4 months old. 225$ Also selling my Pentium IV 1.8 CPU. 140$
July 27th 03 05:08 AM
by La Pedrera Go to last post
0 1,199
8KNXP bios F6e CPU Voltage problems.. by Bob Davis
"Johan Dahlberg" wrote in message ... Hi everyone, I'm having difficulties getting a stable 1.55v for my P4 3.0C CPU with the F6e bios, anyone else having the same problems? The voltage keeps jumping from 1.47-1.55...
July 27th 03 04:16 AM
by Johan Dahlberg Go to last post
2 954
Boot from SATA 81NXP by La Pedrera
I purchased a SATA drive and have cloned it over (using Ghost) and now want to boot from this drive * much faster than my old 10gb ATA one *. I still want to have the other drive connected and accessible. How do I change this? I see the setting in the bios for BOOT ORDER, but when set to SATA it...
July 27th 03 01:54 AM
by Richard Dower Go to last post
5 665
heatsink and fan for GA-7N400 pro by Marc Martuscello
hey group, I have a gigabyte GA-7N400 pro motherboard, I am looking for a heatsink and fan that will fit this board. i am getting an AMD 2600 athlon xp cpu. I will be doing some overclocking. also any input for a video card would be greatly apreciated. i plan to spend about $200 on a vid...
July 26th 03 08:54 PM
by Andrew K. Go to last post
1 438
7N400 Pro restarts by boh
Hi, I have just put together a GA-7N400 Pro system with 2x512MB RAM, 2x80GB WD RAID drives, 10 GB application drive, MSI FX5200, Termaltake 420W power. No overclocking. I think I have all the latest drivers and bios. Sometimes one I access different applications it will just reboot. No...
(Multi-page thread 1 2)
July 26th 03 08:51 PM
by Andrew K. Go to last post
11 877
8KNXP and Zalman CNPS7000-Cu by Bob Davis
I just installed a Zalman CNPS7000-Cu yesterday. The good news is that it is very quiet and cools well even in silent mode. The bad news is that it did not fit my mobo with DPS2 installed, despite indications from others that it would fit. I'd say it needs to be at least 1/8" smaller in...
July 26th 03 04:03 PM
by Axl Go to last post
5 727
GA-7VAX-A and an XP 2100+ @ 333 by NuT CrAcKeR
Hello All, I have been reading up on the B core t'breds, and the consensus seems to be that most of them can run at 166 (333). The thing is, the 7VAX-A board I have only has the switch for Auto/100. There is a place on the board where another switch looks like it could have been placed... IF i...
July 26th 03 05:34 AM
by JKBK Go to last post
3 400
Mouse Cursor dissapears after reboot by Frans Groot
Gary Seven wrote: On Windows 2000 with SP4 when I reboot the moist cursor doesn't come back. this only happens when I Go to Start, then shutdown, and hit restart. If I actually shut off the PC, and turn it back on its there. I am using a Logitech USB...
July 26th 03 03:47 AM
by Sue McCartin Go to last post
2 513
GA-8IK1100 and Mouse Problems by S.Heenan
Gary Seven wrote: I posted on this before but didn't get much of a response. I have a Logitech Optical mouse. When I reboot sometimes the cursor is gone. I flashed the F6 bios, and I installed the latest mouseware from lotitech's site. Still I get the same thing. I also have the...
July 26th 03 03:19 AM
by Gary Seven Go to last post
8 401
GA-7ZXE wrong CPU temperature? by llywiwr
GA-7ZXE When I boot up from cold with a room temperature of about 25 deg. C. my CPU temperature immediately shows as 35 degrees. Is this a fault with this board?
July 26th 03 03:04 AM
by Bob Davis Go to last post
1 963
GA-7VAXP Ultra Chipset Fan Noise by The Maxx
My GA-7VAXP Ultra Chipset fan has started being really noisy. I took it off and cleaned it out and that seemed to help a bit because it was clogged with dust and dirt, but it's still really loud. There are times when it will eventually calm down, but most days it just stays really noisy. I'm...
July 26th 03 02:33 AM
by Jeff Go to last post
3 348
8KNXP: VCore=Fail by Musk
I've noticed this message on the system health screen in bios. What exactly does this mean and is it a problem? I ask because it's always shown this, and yet i've been using my new system with this mobo for 6 weeks with no problems. Everything works great from the latest games to video and...
July 26th 03 02:26 AM
by Musk Go to last post
0 449
2600 XP running at 1262 on a GA-7VAXP Ultra? by John Constable
I've run some diagnostic utilities and they report my CPU (2600 thoroughbred) to be running at 1262. My bios says (my FSB?) speed is 100. I tried to change it to 166 and it failed to boot (rebooted on its own with setting changed back to 100) My questions: 1) can some recommend a good diagnostic...
July 26th 03 12:49 AM
by John Constable Go to last post
3 487
Post New Thread


Display Options
Showing threads 3921 to 3940 of 3996
Sorted By Sort Order
From The
Forum Tools Search this Forum
Search this Forum :

Advanced Search

New posts New posts More than 15 replies or 150 views Hot thread with new posts
No new posts No new posts More than 15 replies or 150 views Hot thread with no new posts
Closed Thread Thread is closed  
 
Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 01:31 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 HardwareBanter.
The comments are property of their posters.