http://search.ebay.co.uk/_W0QQgotopageZ1QQsassZoracleQ2dukQQsosortorderZ1QQsosortpropertyZ1

0 (3BC). We teach people how to build a successful home business, so we are pleased to have your kind inquiry. To share our experience and know how with you is our pleasure. General speaking, there are two steps to start up your own business, and the cost is about HK 1800 (1BC), or HK 4800 (3BC).

Hello, I recently purchased a Proliant 6500 Quad P-II XEON and it contains a Smart Array 6500 Controller card. I have a couple of questions: 1. Are the CPUs upgradable to P-III XEON, and if so, what is the MAX speed? 2. Where may I obtain information on the SA 6500? I didn't see...

Hi! I'm new to Compaq Servers and equipment That being said, I have recesntly purchased a server and other equipment. I have a Proliant 1500 server with the optional 6/200 dual processor board. The controller is a SMART-2/E who's SCSI external interface is 68pin female.

1) KTC9023/256 memory kit AFAIK Compatible with Compaq ProLiant 1200 6/233, 6/266, 1600 6/266, 6/300, 1600R 6/266, 6/300, 3000 6/300, 6/333, 3000R 6/300, 6/333, 5500 6/200, 5500R 6/200. $30.00 http://www.memoryx.net/149026b21.html 2) Compaq branded 228468-001 X 2 Single sided

Anyone out there know where I can download an ISO for this or somewhere I can dload it. I did purchase from Compaq but have to wait 5 days for it. I need to roll out three servers in the next few days. Thanks in advance Joe Smart Start 5.5 CD for ML 370 Gen. 1

Hello esteemed group, I have a Proliant 1600 with a P2 350 MHz Slot 1 processor. I have another P2 Slot 1 processor of 450 MHz. Is it possible to use them both or do they have to be of the same speed? Any problems when running Linux on it? Thanks in advance, Dirk

Im desperatly trying to get at least some sort of Linux distro on my compaq ML-370 SMART-2DH Array Controller , Ive been working on this problem for a week and have been through alot of the compaq how-to sites, fedora makes it the closet {hangs on megaraid) but id really like to get slack 10...

Hello, I have a Compaq Proliant 5500 which came from the factory with (4) 450Mhz PII XEON processors. I recently purchased (4) 700Mhz PIII Xeon's and wanted to see if they would work in this machine. I know the 450's and 700's use the same 2.8v electrical rating so I am assuming the VRM's are ok....

Inherited a Proliant 3000 - 512MB Ram - 7-9GB drives - runs startup ok - after scsi check - says something to affect that drives have been moved arond - need to run ADU (or something like that) I tried downloading the ADU from compaq, but evendentally it is not bootable - any help -...

I've 3 Proliant 3000's that I'm parting out, as well as one Proliant 6500. All systems currently test out fine in diagnostics. Let me know what if anything you may be interested in, fans, boards, whole units if you like... I'm in North Carolina. All reasonable offers of interest. General specs are...

Hey I'm looking for service disk for compaq. This service disk make me able to going in BIOS. If somebody know where I can find these disk, please give me a link or write to my at: Hey szukam dysku serwisowego do compaqu. Dysk ten umozliwia wejscie do biosu. jezeli ktos wiec gdzie...

I have to configure RAID on Proliant 6000 Xeon box. The RAID card that was pitched in Proliant 6000 documentation is 3100ES which uses the built in 3 channels raid in that server. Right now I have SmartArray 3200. I want to know if that is compatible with the Proliant 6000. The issue I am running...

I will soon need to install new Hard Drives into a Compaq ML330 G2 Server with a SA 532 Card. Currently Array A contains a Raid 1 array with 2 x 18 GB SCSI Drives and contains the boot partition, and a data partition. Array B contains 2 x 36GB SCSI Disks, and will not be touched. The C Partition...

Hello there, I want to set up my old proliant 400 with 2 scsi hard drives. For the moment the OS (NT4) is on an IDE drive. When I replace the IDE drive by the SCSI drive, NT4 setup is stops because no hard drives are found (it is possible however to install XP). I suppose this is a controller...

Hi folks, When I perform an assisted install using SmartStart (thanks LC), everything works fine until the very last step: the server hangs on the screen "installing and configuring Compaq utilities". I can only force a shutdown and restart, but then the NT installation starts all...

Hi, I have seen a lot of information being given out here on the 1600 and the 3200 controller card and I am hoping someone out there can help me with a few questions. The company that I am working for may be giving me a PL1600 with 3200 controller (SP340855-01). The system came with 9.1gig Wide...

Have some misc parts including power supply, scsi cd-rom, 4gb scsi drives (4), system board, processor board, smart array controller board, nics (2), scsi controllers (2), lots of 8mb (I think its 8mb) memory sticks, and scsi cables. All were salvaged from working machines, but I can't...

GET YOUR TRIP TRIPS TO DESNEY TRIPS TO HAWAII http://travelexpert2004.us http://travelexpert2004.biz http://gotraveling85.us

When using SYSTYPE from the SmartStart Scripting Toolkit the utility may return "unable to determine system ID" when run on an HP/Compaq server, even with the latest SSSTKSYS.INI that recognises the particular server. The solution is to only run the utility under DOS/Win9X. It consistently returns...