A computer components & hardware forum. HardwareBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » HardwareBanter forum » Motherboards
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Post New Thread
Threads in Forum : Abit Motherboards Forum Tools Search this Forum Feed Icon
  Thread / Thread Starter Last Post Replies Views Reverse Sort Order
Will this Memory work with the NF7-S by Thomas Goldsmith
I was wondering if this Memory works with the NF7-S. The Memory Config at the site does not bring it up for this board. Kingston HyperX KHX3200/512 512MB DDR400 PC3200 Memory w/Heat Spreader a.. New HyperX Enthusiast Grade Modules: a.. Designed and built by the world's largest independent...
December 12th 03 10:42 AM
by Electron Go to last post
1 3,314
NF7-S Memory by Heath Holden
I will be putting together a system within the next week or so using a NF7-S. I want to run dual channel. I will be using it to surf the internet, play Tomb Raider & Madden, & use MS Office. I would like to use 1Gb of HyperX memory, but it has shot up $75 higher in the last week. Will I suffer much...
December 24th 03 02:37 AM
by Heath Holden Go to last post
2 3,067
NF7-S v2.0 Memory Question by Mike
Can anyone tell me whether this memory works with this board? Newegg has it for 157.00. If not, any recommendations. Thanks. Corsair Value Select (Dual Pack) 184 Pin 512MBx2 DDR PC-3200 - OEM Model# VS1GBKIT400 Item # N82E16820145440 Specification Manufacturer: Corsair Model: VS1GBKIT400
November 12th 04 09:45 PM
by S.Heenan Go to last post
7 2,793
my NF7 S2 MBRD doesn't see US Keyboard pressing F8 to get Windows menu by [email protected]
My NF7 S2 MBRD doesn't see US Keyboard pressing F8 to get Windows menu I flashed the BIOS, but still, the problem remains. what is going wrong? did the flash not contain an update for that?!
June 29th 06 11:43 PM
by [email protected] Go to last post
7 2,686
Warning help by David G Misner
Warning!!! DDR Dimm modules should be set from DIMM4 to DIMM1 by order!!! What does that mean???
(Multi-page thread 1 2)
July 10th 03 03:07 AM
by 0_Qed Go to last post
14 2,486
first build.. problem by Christo
Specs: Abit NF7 Motherboard AMD Athlong XP2600+ 512mb Crucial DDR333 memory sony cdrw/dvd combo drive alps floppy maxtor hdd (un formatted was going to do it in XP setup has no files on but has been used as a secondary) GAINWARD geforce fx5200 256 agp graphics card
(Multi-page thread 1 2 3)
September 10th 04 02:45 PM
by ICee Go to last post
21 2,336
Cannot install over 3GB on AW8 Max (meant to support 8GB!) by Peter Hucker
I have four 1GB memory modules (GEIL PC5300 667MHZ latency 3,4,4,8) and an Abit AW8 Max motherboard, with a Pentium D 2.8GHz CPU. I can install any 3 of these memory modules into any 3 of the slots, and it works fine. If I install all 4 at once, I get POST code 4E on the motherboard's POST code...
January 1st 06 05:12 PM
by Ed Forsythe Go to last post
7 2,308
ABIT NF7-S 2.0 and mobile Barton 2500 how much overclock ? by Scott Backular
Just ordered the Barton 2500 Mobile and now looking for a board to plonk it into :) I had a Be6 1.0 well still do worked great with my Celeron 433, then went Asus now i think ill go back to Abit. Can a ABIT NF7-S 2.0 handle mobile cpus the mobile barton 2500 ? I want to have access to all...
(Multi-page thread 1 2)
June 24th 04 05:08 AM
by Scott Backular Go to last post
10 1,957
Question About Motherboard - CPU Combination - Please by Roc
I need to know of a specific combination of a motherboard that WILL NOT support 64-bit mode (AMD64/Intel EM64T ) but will work with a 64-bit CPU (AMD64/Intel EM64T capable). In other words a motherboard model that will take, say an Athlon x64 or Intel Core 2 Duo, where the 64-bit capability...
January 23rd 07 07:50 AM
by Fishhead Go to last post
9 1,856
does the AN8 Ultra support usb booting off usb flash drives by Mark
AN8 Ultra board and usb booting. I'm trying to get a SLAX linux USB pen drive to boot, the manual isn't clear if usb booting off flash drives is supported. In the bios, there's a "removeable" boot option but is that floppy or what? When I set the removeable option as the first and the hard...
May 10th 06 12:51 AM
by Mark Go to last post
1 1,837
Explosive capacitors - and how to replace them? by Doug G.
In article , stacko23 @my-deja.com says... Hi NG! I'm having a big problem: One of the 2200 µF chemical capacitors near the cpu socket of my abit KT7 has exploded yesterday. It just separated in two parts, with a loud 'pop' sound. I was...
(Multi-page thread 1 2)
September 1st 03 03:09 AM
by 0_Qed Go to last post
11 1,786
Stupid Power Supply Question by RHD
Hi, I am building a new computer, IS7 - 2.4C ...its been a while. I have a brand new P4 power supply with the main power connector and the seperate 4 prong plug. My old PSU doesn't have the 4 pronger. My question is:
July 10th 03 02:28 AM
by RHD Go to last post
0 1,764
WD 74GB RAPTOR 16MB CACHE INCOMPATIBLE, Previous generation with8MB of cache work fine. by Justin Piszcz
I have five A-Bit IC7-G motherboards, each of which is equipped with 4 SATA ports, 2 are on the Intel ICH5 controller 2 are on a separate SiI 3112 chipset My old raptors: 1- WD740GD-00FL 2- WD740GD-00FL
December 25th 06 01:28 AM
by Justin Piszcz Go to last post
0 1,747
NF7-S power up problem by Jeff Green
I have just installed a new NF7-S motherboard in my system. Every time I shut down my computer won't power back up unless I disconnect the power supply and re-connect it first. I tried to see if there was a bios setting that might be causing it, but I don't see anything. Any suggestions...
January 18th 04 08:06 PM
by molasses Go to last post
9 1,687
Please HELP! NI8-SLI won't boot - A0 and C1 POST code by [email protected]
Just bought an NI8 SLI mobo. Did the following: - Connected it up with ALL THREE power connectors (ATX12V1, ATX4P1, and ATXPWR1). - Installed my CPU with stock cooler and connected to CPUFAN. - Installed my memory. - Setup the SLI bridge connector on the mobo to NORMAL - Installed my graphics...
June 6th 06 06:56 AM
by Wes Newell Go to last post
5 1,678
problem with nf7 v2.0, 200fsb, 2 sticks ram by Geoff
specs to start with xp2500 (1.833ghz normal speed) 2 x 512pc3200 twinmos m-tec ram nf7s v2.0 running at default values for bios apart from: 200mhz fsb x 9 (for 1.8ghz) prime95 fails with 1 stick of the above ram in the double dimm slots
July 10th 03 01:05 AM
by Lars Winkelsträter Go to last post
5 1,671
AT7-MAX 2 won't power on by Weeble
I recently built a computer for my flatmate. I've built a few computers before, and don't think I've made any particular oversights. Before I describe the failure, here's the specs: ABIT AT7-MAX 2 motherboard Athlon 2600+ XP 2x 512Mb PC333 RAM ABIT GeForce4 Siluro FX5800 with 128Mb RAM Plus a...
July 10th 03 05:27 PM
by Weeble Go to last post
0 1,618
KD7-S fails to boot to POST by Ian
I have just bought a Abit KD7-S, PC2700 memory(512MB) Gainward GeForce FX5200 graphics card, 450W PSU and AMD XP2600+ FSB333 processor. The only time I get to the POST screen, ie the monitor light is green, not orange) is when I erase the BIOS. It comes up with several messages : "Processor...
July 12th 03 05:44 AM
by - HAL9000 Go to last post
1 1,605
BIOS Problems by LrT
Try taking the ram out and booting. Of course it shouldn't boot. But then turn it all off, and put ram back in. See if it resets itself to 266. Or you may have a bad bios. Maybe you could re-flash it. But that may cause more problems if it fails to flash. Maybe put a different stick of ram in...
July 8th 03 08:36 PM
by LrT Go to last post
0 1,533
AI7 Temps & Water Cooling Considerations by Jim
Abit AI7 (BIOS 14) P4 2.6C @ 2.85GHz (13 x 219MHz) Coolermaster Aero 4 HSF 1GB (2 x 512MB) Kingston HyperX PC3200 (@ 219MHz, 2-3-2-5) The memory tops out @ 219MHz, and although the timings remain TIGHT, I can't get a single MHz higher reliably, even if I relax the timings COMPLETELY, kinda odd. ...
January 10th 04 05:28 AM
by Tony Go to last post
7 1,492
Post New Thread


Display Options
Showing threads 21 to 40 of 895
Sorted By Sort Order
From The
Forum Tools Search this Forum
Search this Forum :

Advanced Search

New posts New posts More than 15 replies or 150 views Hot thread with new posts
No new posts No new posts More than 15 replies or 150 views Hot thread with no new posts
Closed Thread Thread is closed  
 
Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 02:22 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 HardwareBanter.
The comments are property of their posters.