I just tried to flash my bios again. F6 -F7 -F8 It will not boot. It gets thru the the raid boot process then updates the changes ok. Then bam! 99's ocross the screen. Does this mean a reload of OS? It recognizes my sata hdd's in the bios as ide 2master and ide 2 slave. I actually have the option...

Normal use seems to average 50 celsius. When I run my ATI screen saver it jumps into the 60's. Also the fan runs louder and louder as the load increases. Should I reseat my CPU with new heat sync? I am currently using silver heatsync. It has been running ok since I built it (3 months or so).

Will this heat sink fit on the 8knxp?

I could not get my sata raid array to work. It would not see the drives. However I did get the intel array working. I would like to use the sata raid though. But when I put my cables on the sata I and II connectors it would not go into setup or boot. Anyone else with this problem?

3D Pipes - 46C, Aquarium 2 - 52C, ATI 9800 demo's and screen savers - 58C to 60C. It would appear the 3D rendering of the ATI card can really heat the CPU up!

i ran the iaar352_enu.exe and installed to floppy, the on;y file i'm getting is iastor in a driver folder. This will not work for clean install (f6). I need txtsetup.oem, iastor.sys and a cuople others needed. Am I doing something wrong or is 3.5.0.2*** the only driver available?

I flashed from f6 - f7 - f8 - f9 and it actually booted reading my raid array. One thing though my dmi reads f6 12/25/03. Huh?

I'm considering adding a stripe 1 array to the gigaraid controller on my board which already has a sata raid 0 array on the ich5r controller. I suspect it will go fine. Any suggestions or "tips" would be helpful.

I have already installed Windows Xp Home and my motherboard doesnt detect anything in IDE2 or IDE3. I believe i need to install the VIA IDE RAID drivers in windows and i do not know how to do this. I need simple step by step directions if anyone can help me out, i am computer illiterate so please...

http://global.giga-byte.com/MotherBoard/Products/Products_GA-8I915P%20Duo%20Pro.htm The link above is my GA-8I915P Duo Pro Motherboard and you can look at the manual after I explain my problem. First off, I know for a fact that my cables are connected correctly, jumpers are set right and the...

Based on all of the glowing reviews I was a day away from ordering Abit's IC7 when I stumbled on their forum and found they had a serious issue with their onboard sound. So now I'm looking again. These two Gigabyte boards also seem to be very well rated. I have some questions: - Are there any...

You mean now I can SHOOT YOU in the back and further BLUR th' distinction between FANTASY and REALITY?

Okay Now I have a question. I crashed my Webserver last week (software crash) and everytime I try to reload the raid settings keep going away. I save them as per the destructions that I used when I set it up originally but no-go. it does the software load cycle including loading the raid drivers...

I want to buy 2 x 2GB of DDR2 (not DDR3) 1333Mhz memory. Is this DDR2 PC10664? Who makes this? regards, Beemer

I have two SATA 500GB disks which previously were working with my failed ECS K8N SLI Extreme motherboard. It had two Raid controllers one was NForce4 and the other a Sil controller. I cannot recall which one was being used but it was definately RAID 1. Now I have a Gigabyte GA EP45-SD3P...

I have a GA EP45-DS3P motherboard and now have installed XP Pro SP3. I now want to add a RAID 1 pair of drives just for data storage. Despite reading the GA manual several times I cannot see how to install the Intel Matrix Storage raid controller in the following structu - Windows is on a...

I want to run a RAID 1 on two additional drives. I do not want raid on my Windows XP drive. It does not appear possible to do this as the F6 key (which loads the driver from floppy) only is functional during the XP installation. Can anyone help? Beemer

I want to run a RAID 1 on two additional drives. I do not want raid on my Windows XP drive. It does not appear possible to do this as the F6 key (which loads the driver from floppy) only is functional during the XP installation. Can anyone help? Beemer

My GA EP45-DS3P has six sata ports (0-5) I have all in use and my RAID 1 pair are connected to ports 4 and 5. I have used F6 when installing XP to load the Intel ICH10R driver. I then used Ctrl-I to load the Intel Matrix Storage manager to configure my SATA 1 pair. My Bios Rev 7 has CMOS...

What is the correct procedure to use the illuminated cmos reset button on my GA EP45-DS3P? There is nothing in the manual/ regards, Beemer