I have trawled the Gigabyte website but canno find confirmation of support for the new AMD Winchester 939 pin processors! Can anyone shed any light on which models are compatable please?

My two 512 MB sticks of Corsair memory don't work on this mobo at 200 MHz. BIOS shows 166 MHz. When I use a single stick I get the full speed. I cannot set the speed in the BIOS, since the clock speed for DDRAM is grayed out. When I set it via EazyTune it does not keep that value. How can I set...

My two 512 MB sticks of Corsair memory don't work on this mobo at 200 MHz. BIOS shows 166 MHz. When I use a single stick I get the full speed. I cannot set the speed in the BIOS, since the clock speed for DDRAM is grayed out. When I set it via EazyTune it does not keep that value. How can I set...

My two 512 MB sticks of Corsair memory don't work on this mobo at 200 MHz. BIOS shows 166 MHz. When I use a single stick I get the full speed. I cannot set the speed in the BIOS, since the clock speed for DDRAM is grayed out. When I set it via EazyTune it does not keep that value. How can I set...

To all Cognoscenti, Greetings! Does anyone have any experience with GigaByte GA-7N400-L motherboards? Are they reliable or troublesome? Any comments would be appreciated. Andy

I have replaced almost everything on my desktop computer apart from the case and the power supply to try and find what the problem is and still getting the exact same symptoms from the new components. It sounds obvious that I should replace the power supply perhaps or even the case which has a...

Since upgrading to this board I have been having problems launching Nero Burning (latest V5). The Plextor 48/24/48 IDE CDRW takes an age to recognise a blank CDR and Nero stops loading till it is happy. Sometimes the program stops responding altogether. I have updated firmware on CDRW, updated...

GA-81915P Duo (Pro) How do I set the bios settings to find my two IDE Hard Drives and one CD-ROM Drive My Hard Drives jumper settings are set to Master and Slave on IDE1 Connector My CD-ROM Drive is set to Master on IDE2 Connector When both are plugged in, I only see what is on IDE1 only? I've...

Hi, I've got a GA-7VT600 1394 that I can;t seem to get to work. No matter what I do I get the Bios beep alarm that means cpu overheat. (The up and down tone). The system runs for about 4 secs then powers down. It's never got as far as even loading the BIOS. The CPU is a brand new Athlon 2600....

After having a nightmare two days trying to install XP Pro on my two Maxtor sata 80 gig HDD's as raid 0 during which I received constant IRQL Stop errors I tried the older Sil3112 sata raid drivers which came on the motherboard support CD. This allowed me to install XP OK. Now however I notice...

Hi I'm looking at upgrading my mobo to the giga-byte GA-7N400 pro 2, however I was wondering if this board has a power point for the power cable for my Nvidia FX55XT graphics card. If it does not can anyone recommend an extremely similar board with all the features of the pro but with the...

Help is needed if possible. Thanks again. When I put the drive on IDE 1 it does not pick up Windows 2000 to boot only when I put it in IDE 2 or secondary does it work..advise please.

Hi all, I just bought a cheap IDE RAID card from EBUYER (it is an EIO card based on Silicon Image 1680 chipset) but my v1.5 6BXD motherboard won't recognise it - on boot the card's bios does not appear. It appears when I put the card in a more modern machine. Any ideas how to get it working? I...

Hi all, I have a dual processor 6BXD board but it is v1.5 - can anyone tell me what the fastest processor for this board is? TIA Andy

I have been using this computer program for a couple weeks now and i am very pleased with the results so far. its a software fatloss program, if your looking for a diet/weightloss plan i reccomend you check this place out first: http://fatloss9.50webs.com

I have an old 8PE667 Ultra 2 motherboard. I am using the computer for running surveilance camera hardware and software. If I have a power failure, I have to manually restart the computer. I want to leave the system unattended for about 3 months, and would like the computer to start up its self when...

....hard drive that a Gigabyte 7VT600-1394 mobo with BIOS version F7 will handle without using any drive overlays or RAID?

I have a GA-7VT600-1394 motherboard. When I got the board, it had Bios rev. F5 and everything worked seamlessly with no problems. About 3 months ago, I flashed the bios to F7 to ensure large hard disk support and every since, at every power up I get a bios error "Some bios settings have prevented...

Whats the correct PCIE Speed on this mobo s'posed to be set at in the bios? Right now its at 100 but it seems if its 16X should be 133MHz? Thanks. -- A:\DOS\ver MS-DOS version 2.11 A:\DOS\_

Will current AMD64-939 mobos support this upcomming chip? Thanks.