Here are my specs Ic7-G bios 1.4 P4 2.6C 800Mhz FSB 2 - Corsair PC3700 512MB TwinX 2 - Western Digital Raptors 36G in Raid 0/Intel ICH5 ATI 9700Pro 128 MB or Gforce3 Ti200 64MB Antec True Power 380 or 480 ( tried both )

Hello, I have a KT7A-Raid motherboard , when I either reset, warm start, or even modify cmos, my mother board hang on, without any bip. I have to disconnect power supply, and after 3 to 6 secondes, it runs again. but when I shut down XP, and run again further , same problem happened, and I have...

ahh i blew my nf7 up (i think so anyhow) this is the end for me, my beloved nf7 that was super quick and brilliant has blown, Im now stuck with a poor KT600 chipset board (MSI KT6V) isnt bad though anyhow can anyone tell me if there is a way to test mainboards without sticking them in a puter?...

i have an abit NF7 i know that much, i purchased from ebuyer from the net, one thing however is that I am not sure if this NF7 is a version 2.0 or not I am right in assuming that the version 2.0 boards allow for FSB of up to 400 mhz on the CPU I would like to know if there is any way i can find...

Off topic, but i have tried most of the MS newsgroups with no luck... i do own an abit board though i had a fully working computer until 20 minutes ago Windows XP freezes at startup, whenever i click on my account it freezes at "loading personal settings" The only time i can get past the loading...

i have a standard nf7 and am looking to overclock, im not sure what FSB the board will support i had originally thought it was 333 mhz however this page: http://www.abit-usa.com/products/mb/comparison_amd.php says it will take 400 mhz FSB

I have 3 modules of memory on my NF7 v2.0 board. 2 of these are PC2100 266 mhz 512 mb modules. I have these in the two slots closest together. In the second channel i have a PC2700 333mhz 512 mb module. When i boot the memory displays as frequency 266 mhz... however there is 1.5gb of memory being...

hi i was wondering how to hook these up? i know there are two blue coloured usb connectors on the board I am using one of them! However the case I have doesn't seem to have anything to fit these connectors that come from the area of the USB ports on the front. There are a few loose cables that...

got my system rolling after a hard slog at installing and formatting the hdd one minor problem now whenever windows alerts me to something the motherboard "BEEPS" once it is quite annoying... i have took the speaker jumper away but is there anywhere in the bios that will let me disable this i...

sorry to keep nagging but this is probably the last major problem i will face that i wont have a clue how to solve.... I have went into the bios and set the cd-rw/dvd combo drive as primary boot device.. it boots and as usual displays "booting from ATAPI CD-ROM:" i open the drive while the...

Specs: Abit NF7 Motherboard AMD Athlong XP2600+ 512mb Crucial DDR333 memory sony cdrw/dvd combo drive alps floppy maxtor hdd (un formatted was going to do it in XP setup has no files on but has been used as a secondary) GAINWARD geforce fx5200 256 agp graphics card

This has been worrying me for a while today, I have purchased a ABIT NF7 (not an NF7-S) over the internet with the other components for my first build.. i have also purchased an AMD XP2600+ with stock fan and a GAINWARD Gefoce FX5200 256 mb gfx. I plan to have a DVD/CD-RW combo drive and an 80 gb...

Hi there! I wonder if any one has any ideas on a problem that is kicking my butt! I have a Abit KX7-333 mobo with a Athlon/xp 2400 retail chip on it.... It also has a single stick of 512mb ddr333/pc2700... This board operated for over a year in one of my machines..... Since cannibalized for...

Hi, I just recently bought an AGP G550 off the internet and am trying to make it work on an abit kt7a board. I'm getting refresh problems and I am locking quite often. I googled for a bit but didnt find any definitive answers other than the AGP version of the 550 may or may not work. Is there...

Just got a new heat sink and fan (Arctic Cool). After I installed it and turned on the machine I got the Bee-boop (CPU overheating alarm). Needless to say, I immediately shut off the machine, checked the fan (it was running) and the CPU (it was cold to touch). Very weird! I then reapplied...

System: ABit KV8 PRO m/b AMD 64/3000+ SATA WD400JD HDD IDE WD1200JD HDD 1 gig RAM OS = Win2000 Pro I think that's all that's pertinent, let me know if more info is needed. The question is: whenever I try to start the system with the SATA HDD connected, it stalls at the windows loading screen (logo...

Hello, Tonight I discovered that my system is not detecting the IDE primary master or slave, or the IDE secondary slave drives. I tried auto-detect in the bios - it shows the right settings for the master (20 gig Maxtor) but will not detect the 15 gig Maxtor slave, and will not load either drive....

I just got a new Abit microATX board and did not see any utilities on the CD to monitor system parameters. Do they have one? Thanks, Clark

Hi all, Does anyone know why there are no drivers for the above mobo on Abits site? The drivers for every mobo EXCEPT this one are there!!!?? Where can I d/l latest drivers for ABIT KX7-333r? TIA:)

Hello Fellow Techies: I am setting up a new AN7 motherboard with an NVIDIA nForce2 chipset. I have the latest BIOS version from the ABIT website. My Radeon 7500 Video card however does not function properly. While I have the resolution set to 1152 x 864 True Color still I only see the colors...