Running K8V SE with: version :08.00.09 Build Date 2/09/04 I see a bios update on asus support pages dated 08/05/2004: http://www.asus.com/support/download/item.aspx?ModelName=K8V%20SE%20Deluxe&Type=All But it has this little warning on it:

Ok here is my problem: my motherboard doesn't see my serial ata harddrive. I am thinking that it is something to do with the drivers. I just don't understand how the motherboard could lose something like this. I had a problem similar to this and fixed it by manually loading the drivers. (...

Hey guys, I have some problems with my new mobo. I cant install the AGP slot correct. In the device manager i see a question mark before "NVIDIA nForce2 AGP Host to PCI Bridge". If i get the proporties of it, i get next messages in the device status: "This device cannot find enough free resources...

Sorry if this has been asked many times before but i have only just got this K8N-E Deluxe mobo and am a little new to 64 bit processors. My question is this, if i turn on both q-fan and c'n'q the fan comes on and then stops, and the bios reports cpu fan fail and halts the system. If i turn c'n'q...

Hmmm but maybe that's only the assembly ? whatever that is ? Probably the metal casing or something ? The main label reads: "Made in thailand" Also it's quite disappointing that it did not came with a manual, or screws to screw it into place. Fortunately the manual can be downloaded from the...

Got a 160 gig SATA, i have no probs with it or will. On Tue, 16 Nov 2004 15:07:25 +0100, "Skybuck Flying" wrote: Oh-Oh Lol Could this be the first sign of trouble ;)

I have a Asus P4PE MB with the Promise FastTrack376 controller onboard. The system is configured with a DVD reader on the Primary MB IDE MB connection and a CDRW burner on the Secondary MB IDE connection. I have a Promise Ultra133TX2 card in slot 5 and have two Maxtor 60 GB DiamondMax 9...

I am looking to setup a Raid 0 array using 2 - 120G Western Digital drives. Is there any advantage (speed, reliabality) to using the Via controller over the Promise controller or should I use the Promise over the Via. I will be partitioning the 240G array into 3 partitions, with the main partition...

Hi all, I will thank any help concerning this problem - I am not at home now but I am thinking saving some time by asking all the "pro" guys here. I have a P5P800, no floppy, a WD 200Gb S-ATA drive, an IDE DVD-ROM, IDE DVD-Recorder and a IDE HD 40Gb. I have XP running for some time and no...

Hello all, I've been struggeling for 5 days now with the following issue: Last week I bought 3 PC3200 modules of 512MB from Transcend. When I clock these 3 DIMMs at 333 MHz my PC crashes after a few minutes, sometimes I even see blue screen flashing by. When I clock these 3 DIMMs at 266 MHz...

Hi folks, i'm currently running a P4 2,53@2,85GHz (FSB533@600) with my P4G8X Deluxe (Rev. 1.02, BIOS 1007) and i'd like to upgrade to a P4C (FSB800) with 2,8GHz or more. I know that the E7205 Chipset only supports FSB400 and FSB533 CPUs, but maybe someone tried it with a FSB800 P4. To make a...

I have 2*512MB ECC Registered DDR but my Dual Athlon mobo is dying (MSI K7D Master) with burst capacitors. Hoping to reuse the RAM and one of the CPUs in a cheap Athlon XP board until I upgrade next summer. Thanks, Chris

I have a p4c800-e dlx mb to which I've had only a one sata hd connected to intel sata 1. Tonight I installed a second sata hd connected to sata 2. I went into the bios and followed the instructions from the manual: onboard ide operate mode set to enhanced mode, enhanced mode support on set...

I have recently built an new system which has been running well for the past fortnight. Until this morning. I had been running a 10% overclock with no problems but decided to try my luck a bit higher. I changed the overclock mode to manual and tried for 225Mhz on the FSB. Windows XP Pro booted but...

there should be a setting in the BIOS to disable that shutdown feature..disable it while you have a stock cooler on and then change it.

I want to be able to boot with no keyboard or monitor attached. In the past I have always found this option in the bios but I dont see it on this box. Any ideas on how to do it?

Site and Features: http://www.eigensearch.com Search engine, eigenMethod, eigenvector, mathematical, manifolds, science, technical, search tools, eigenmath, Jacobian, quantum, mechanics, manifolds, science, physics, chemistry, law, legal, government, home, office, business, domain lookup,...

When I push the power switch, my PC powers up but does not boot up. Nothing is displayed on the monitor and no disk activity. It stays in this state until I press the reset button and then begins to boot normally. All DIP switches are in the default state (off). I have a 350 watt power supply,...

This is a brand new machine. Here are the components: Asus A8v Deluxe motherboard with bios 1008.002 beta (I used ALT-F2) AMD Athlon 64 3400+ Antec Solutions case with 350w Antec Smartpower PSU TI-4600 AGP video card 1GB Kingston Value Ram PC3200 (KVR400AK2/1GR) When I go first start it up it...