After about 2-3 hours of sitting idle, when I return to my system and attempt to load something new it will "hang" for 1-2 minutes before it loads the program (IE, explorer, outlook, etc). It will continue to do this until I reboot the system. It also becomes unstable, so even if you were patient...

visit www.bioschips.webhop.net For Replacement chips $15 re-flash of existing chip $8

I have TWO NF7-S systems and they both hesitate repeatedly when any sound card is present. No sound card, no hesitation. It hesitates whether or not I overclock my 2500+. What BIOS settings should I adjust to stop the freezes?? Thanks!

I've just installed a Zalman 7000A heatsink/fan to try to quiet down my system. Unfortunately when I plug everything back in and power up, the system only gets power for a few seconds then everything turns off. During those few seconds all the fans spin up, so everything is plugged in properly, the...

Hello -- Does anyone know why the VP6 is limited to 2GB of RAM, when the Pentium III can address 4GB? Thanks, Route User -- ABit VP6

I have upgrade my bios of my nf7s rev 2 with 1.9 but the system can't boot nothing appear on screen,NOTHING.... I can"'t do anything I AM BLOCKED..... WHAT SHOULD I DO, PLEASE........... i read on manual that after i had to clear CCMOS with jumper during few muinutes but nothing change, no...

I have TWO NF7-S systems and they both hesitate repeatedly when any sound card is present. No sound card, no hesitation. It hesitates whether or not I overclock my 2500+. What BIOS settings should I adjust to stop the freezes?? Thanks!

I've got TWO NF7-S systems and they BOTH hesitate for a second or two at a time at a rate of maybe two or three per minute. Changed power supplies, memory, even the motherboard to a GigaByte GA-7N400 Pro2 and the problem persists. What could possibly be wrong? I've tried the internal sound and...

I have a VP6 with 1 leaking 1500uF 6.3V cap & a bunch of bulging caps of the same kind. They're all Jackcon. I'd like to know if someone knows of a company/someone that replaces caps in the EU. I'm in Portugal. Its really a shame to throw this board in the trash for a problem i could probably fix...

Will it handle a XP2400+?

Just ordered this board to use with watercooling. Same Hardware features as IS7, but has 3.2vdimm and all the new uguru, blackbox etc. features. cheers

Why ? Gandalf Glimlach - be wary of OZC however Richard Rollins wrote:

visit www.bioschips.webhop.net For Replacement chips $15 re-flash of existing chip $8

I am currently using a KX7-333R mobo and I have 3 sticks of PC2700 512MB memory. I have followed the direction for loading the memory into the DIMM slots (ABIT goes 4 to 1) and everything seemed to work great. then I started getting a blue screen doing a memory stack dump. I then removed...

I Have a Abit KD7A motherboard with a Barton 2500+ CPU. All the L3 cpu straps are intact and uncut so the CPU is unlocked. However I can't change the multiplier. When I use the softmenu and user configuration it says it changed it but it doesn't. The boot up remains locked at 11x multiplier. When I...

The MB recognizes them fine on the secondary channel. As a matter of fact I copied the drives from 80GB drives on primary to 120gb on secondary, but when I install these 2- 120gb drives in the primary position the bios fails to see them. What gives?

test only

I'm considering an ABIT NF7 V2.0, maybe a Barton 2500 or a bit higher. Mostly I want good performance on disk i/o since I do a lot of work with large wav files and compression (SHN, FLAC). So I'm thinking of raid with SATA. But I've heard some bad things about SATA on the NF7. Not too much here on...

Hello, I have: Abit TH7II with P4 1,6 L2 256kb Kingston 2 x 128 PC800 RDRAM. I would like to upgrade the processor. But the only available P4 processors have a fsb of 533 (4 x 133). In de bios i can select e.g. for 133 mHz and a multiplyer to 20, so i get 2,66.

I just got this board set up and the guy who set the board up put the HD and DVD drive on IDE port 2 and the Writer on IDE port 1, i just tried to change the boot order and the system wouldn't boot at all. It works (only works) if i have it configured the way the guy set the board up. Does anyone...