P.S. I used a 400w antec, some of the cheap ones are sometimes not to good. good luck "res07mnf" wrote in message ... I had the same problem setting up my board using 300w Antec, 300w is not enough even though the manual says...

Using bios 1006 (i think) When I turn on the Enhanced IDE mode my western digital drives on the regular IDE port come up as udma-2 not 5. In Compatability mode they come up as udma-5. What's up with that? Not only that_ the drive performance sucks. -be

Just wanted to let everyone know that i replaced the usb/firewire assembly and it now works. thanks again for everyones input Eric

It seems the 1012.004 bios is 400 Mhz too low in reporting the type of processor... Odd. Agree. And how could something so glaring "off" have made it by the beta testers? I'm seeing the same exact problem Stephane has reported and. I think, also the 400mhz issue you have found. (I have the...

I would like to bring up a problem previously posted here on the continuous two-tone beep of a p3b-f board. Since then I got a "Computer Main Board defect Post Card" I inserted it first in a PCI and later in the ISA slot on my p3b-f motherboard, hoping to get a better clue on the cause of the...

Hello, I have the P4P800... and I think BIOS 1005... How can I set the AGP to 4x rather than 8x? Thanks

Dual Lan what means? 3Com 3C920B-EMB I use it for my cable Internet conection. NVIDIA nForce MCP Networking Adapter and 1394 Net Adapter. What can I do with these? I'm novice in computers. Please help.

I use DVRex RT and I'd like to build a new PC.. Now I have a doubt about motherboard and the processor: INTEL Pentium IV 2,8 GHz FSB 800 MHz and ASU P4B533 (845E chip) motherboard. Are they a good couple? Does the ASU P4B533 work fine with that processor (800 MHz)? Does that motherboard support...

In article , "Torbjørn Burchard" wrote: I'm trying to get some info on this board. Unable to get it from www.asus, so here I am.. What I wanna know is how many MB ram are there on the onboard graphic chip? And how many...

1. I also have the A7N8X deluxe, and I noticed the same thing. I kinda figured it's the PCB2.0, Rev 1.xx... As in, now that the PCB is at 2.0, they can still do new revisions of it.... maybe that's not correct, but that's what I went with ;) 2&3. Sorry, no help. -Lenroc "Chris"...

I just recently installed an A7N266-VM, AthlonXP 2100, 256MB DDR PC2100 Ram, Win2000 Pro, Standard 48X CD, 36X Burner, 1 Gig JAZ Drive connected to a SCSI card and standard other pieces and parts. After shutting down the computer and restarting I will get a BSD saying that the boot device...

"Stephan Grossklass" wrote in message ... BDW schrieb: Here is an email I recently received from Asus. I tried these drivers and they prevented XP from starting! (thank goodness for the "use last successful...

"Odie Ferrous" wrote in message ... Guys, Thanks all for your replies. However, having been deeply involved in computers for 16 years, and having owned two computer companies, I can assure you that I am not a ...

On Sat, 21 Jun 2003 09:29:25 -0400, "Robert Sudbury" wrote: I was able to borrow a Maxtor 6Y080L0 80GB DiamondMax Plus 9 ATA133 7200rpm 2MB HDD and it is similary affected as the Maxtor 6Y120L0 120GB... Actually it was worse in Cable Select by about 15%. The...

(Paul) wrote in message ... In article , "John Smith" wrote: Yep, I was about to use AFUDOS to upgrade from 1004.4 to 1007 today but then came...

Sorry if this has been asked numerous times before, but I'm looking for an updated answer... I'm pondering over the same deep eternal question of mankind: A7N8X or NF7-S? Their prices differ by only 8 bucks at newegg, hence the difficult decision. (a7n8x = $130; nf7-s = $123).

"Robert Sudbury" wrote in message ... The thread was getting a little long so I've digested the history for clarity... I have yet to determine if this is a READ/WRITE, BIOS, ATA133 or nForce2 problem. I need to...

On the A7V8X there is a specific Bios choice of booting from SATA first, as well as setting it as the first boot option in the boot sequence. They are not on the same BIOS page. Is it the same with your mobo?

My mistake about the Promsie part. That part is on the P4C800 Deluxe. The P4P800 Deluve uses the VIA IDE RAID. You might think the VIA IDE RAID works OK, but read the reviews. It blows chunks. Big chunks. High CPU usage, only fair performance. Probably doesn't work right with some...

Which all in one drivers am I to use? I see a few different kinds, like 1.16, and 2.42. Which are right for my mobo? -- Kiss my arse...