|
|
Updating Firmware on AIT50 Hotswap by
Will
How do you update the firmware on the AIT50 Hotswap tape drive? I would
prefer a Windows-based utility for doing this if one exists. The Compaq
tape drive floppy set of seven floppies is just hanging on our Proliant
6400R, and I don't see a way to get it to do the upgrade correctly.
--
Will
|
|
2 |
236 |
|
|
SCSI ASYN Mode by
Will
Can someone please confirm if a SCSI hotswap drive comes up reporting its
speed as ASYN, does this mean it is limited to 1.5 to 5 MB / sec? What
causes an ultra-80 device to back down to that speed?
--
Will
|
|
3 |
614 |
|
|
|
March 7th 06 07:45 AM
by Will
|
0 |
224 |
|
|
Using MSA50 As SAS JBOD? by
Will
The MSA 50 JBOD SAS enclosures have some kind of high density mini connector
on them that mates to the SAS RAID controllers like the P600. Does HP make
any adapter that would allow us to use these boxes as a pure JBOD solution?
I am trying to set up a testing station for SAS drives, so I need...
|
July 3rd 07 02:50 AM
by thomas
|
6 |
824 |
|
|
Smart Satrt CD for Proliant 5000 by
William
I have recently acquired a Proliant 5000 machine. Unfortunately the
SmartStart CD for it has been lost. Does anyone know where I can get one
from?
--
/* =============================================================== */
I know you believe you understand what you think I said, but I am not
sure...
|
|
5 |
560 |
|
|
RAID drive replacement help!! by
WipeOut
Hi,
We have a ML370 that has a 5 disk RAID 5 array.. One of the disks has
the red light flashing and the event log says the status is "predictive
failure".. I have just ordered a new drive which should be here in the
next day or so..
Now for the question..
What is the procedure for replacing...
|
|
7 |
1,135 |
|
|
ML330E system board by
wireman via HWKB.com
I've picked up a used ML330E system board (230540-001) which seems to have
been common in qute a few Compaq server models. It has a 933Mhz CPU (or
thereabouts) and various PCI's including features board, network card etc.
My intention is to use it in a standard ATX tower as a server on my...
|
|
1 |
849 |
|
|
Compaq Smart Start CD by
wolf242
Nut Cracker, I am also searching for a SmartStart 5.5 CD. Need it ASAP,
Can you help?
|
March 19th 06 10:49 PM
by Paul
|
5 |
405 |
|
|
Proliant Server, simple question by
Wolfgang Haunzwickl
Hi,
a customer gave us 2 Proliant (DL380 and ML370) servers to install W2k3. That
worked OK, but when booting the systems they do not show the little white
square in the right upper corner, but ask to
Press F1 to continue
F10 for System Partition Utilities
That is not good as the systems shall...
|
March 7th 05 05:50 PM
by Tony
|
6 |
457 |
|
|
RA4100 Redundancy by
WS
We have an RA4100 with dual RA4000 controllers that, a long time ago, was
set up for redundancy. What I want to do is remove this redundancy, so that
the second RA4000 controller in the unit operates as a separate path to the
same logical drives.
What piece of software/hardware controls whether...
|
|
4 |
464 |
|
|
Question on P600 Controller Slot Change by
W[_3_]
I have a bit of a problem with a DL385 server using two P600s and would like
some advice. The initial installation was done in error putting the boot
device on an internal P600 SAS RAID controller in slot 3. Later on another
P600 was added in slot 1 that connects to an external array on an...
|
January 10th 09 03:05 AM
by W[_3_]
|
2 |
4,243 |
|
|
SATA Hardware RAID on a DL-320 by
you know who maybe
Can you do this? I can't find the option. It seems in the BIOS you can
select to enable the SATA RAID but it says it's a software RAID, which seems
strange. Software raid in the BIOS? It also says SmartStart does not support
this configuration. I'm using the SATA backplane.
|
|
0 |
176 |
|
|
|
October 14th 04 05:56 PM
by Zuri
|
0 |
299 |